M. M. Factors


Go to content

ProLOOK

ProLOOK


Pro-look Specialist Anti-Rust Treatments, Coatings & Cleaning Products Like:- Pro-look FlexyOil Coating vehicle chassis box sections under body wax and protective coating.

ProLOOK FlexyOil Coating

Unlike most under body coating FlexyOil is easy to spray, wipe on with a cloth or brush yet when it dries out it remains in a constant flexible state so does not run off the panels in warm weather to block up panel drain holes leading to more rust like some products.

PREPARATION : For best result ensure surfaces to be treated are clean and dry, any rust areas should be previously treated with ProLOOK 3 in 1 Rust Converter before applying ProLOOK FlexyOil Coating, suitable for Inner Door Skins, Inner and Under Wheel Arches, Chassis Box Sections, Battery Boxes, Under Body Sections, Metal Brake & Fuel Pipes along with 1,000s of other applications.

APPLICATION: There are several low cost sprayers available on the market from hand trigger sprays, hand pump with pressurised container or specially designed under body coating guns to run off an air compressor, if possible try to apply on a non humid dry day without high winds, always when lifting or jacking up any vehicle ensure the vehicle is safe and secure before starting, cover or mask all surfaces not to be coated to avoid overspray along with ground covers, always follow Health and Safety along with the relevant vehicles safety notes, Always shake can to ensure the contents are correctly mixed before use (repeat this at regular intervals, also in cold weather if required by standing the can in warm water the FlexyOil will reduce in viscosity this may especially be beneficial if using a fine nozzle spray ). Give a liberal coating to any substrate requiring treatment pay special attention to seams and overlapping panels, be careful not to apply too heavier coats on vertical panels as this may have a tendency to run and possible block drain holes (always check all drain holes are not blocked a few days after applying the coating)a brush or cloth can be used to fade out runs, allow to dry before using, some dripping may be seen this is quite normal and will stop once the FlexyOil has fully dried, (ensure FlexyOIL does not come in contact with tyres as this may cause skidding) it may be necessary to open windows when using for the first few days, as the coating may not have completely dried out. A second coating can be applied after a week or so to re-coat any parts that are not adequately covered. Clean any splashes to paintwork, spray guns and brushes immediately after use with white spirit, if hands have come in contact with the FlexyOil clean using ProLOOK Citrus Beaded Hand Gel or warm soapy water.

ProLOOK FlexyOil can also be used as a temporary protective coating for components, farm machinery, equipment, and other unpainted metal parts before storing, by spraying or wiping a coating of ProLOOK FlexyOil over the unprotected surface with a spray gun, cloth or paint brush, before reusing remove coating with white spirit.


Pro-look-hand-gel
Pro-look-hand-gel is a heavy duty lemon citrus beaded hand gel very tough on dirt but extremely kind to hands,

Rub in a small amount of hand gel in your hands and by rubbing the hands together the polymer beads help remove the toughest of ingrained dirt and grease, rinse off with clean water, before drying your hands, to leave your hand nice and clean with a light fresh citrus fragrance.

ProLOOK 3 in 1 Rust Converter

Pro-look-3 in 1 rust converter is a truly outstanding product designed and tested on ships and oil rigs to fight the toughest of weather the north Seaís can inflict on the metal structures, with its salty water and high winds constantly trying to corrode away the metal, now exclusively available from M. M. Factors for garages, classic cars and bikes and DIY use, at amazing prices, it stops rust seals from further rusting and primes the metal all in one application, for best results remove any loose or flaking rust ensure the surface is clean and free from loose rust this unique product can even be applied to damp surfaces, shake bottle (never stir with metallic objects or this will start the curing process that will ruin the whole batch) to thoroughly mix the contents before pouring out sufficient quantity as needed in to a non metallic container, apply with a metal free brush or suitable sprayer, applying a even liberal coat do not try to recoat (a second coat can be applied following the complete drying and converting process see below)
NEVER pore any unused liquid back into the bottle.

THREE STAGES OF CONVERSION.

1) The white liquid is applied to the rusty surface which immediately starts the conversion of rust by sealing in the rust and converting the rusty surface into a hard impregnable coating.
2) As the sealing and conversion is taking place the white liquid starts to change to a blue colour as it finally gets to work on the rust surface.
3) When the liquid is finishing itís conversion, the now blue liquid become black before getting harder and harder until the surface is completely sealed. (this can take up to 24 hours to complete the process and will be ready to apply paint when dry or within a few days).

Although the coating can be over painted directly we recommend a primer is used directly on the black hardened coating to avoid bleed through.

This conversion only works on rust so if there is no rust or it comes in contact with a non metallic surface the process will not completely take place and the finish may remain in a milky blue state, all though eventually it will harden to allow over coating although this may take several days to complete.

Buy Exclusively on www.sell-up-north.co.uk


Click On Trade Specialist Vehicle Consumable Supplier through M. M. Factors | mmf@clickontrade.com

Back to content | Back to main menu